SKYSCAN DIGITAL
ATOMIC ALARM CLOCK

SkyScan Digital Atomic Alarm Clock, retail $TBA
Manufactured by SkyScan (www.skyscaninfo.com)
Last updated 04-06-10



(IMPORTANT!!!)
I've had this for quite a few years now; that's why it does not look brand spanken new in the above photograph!!!

This product does not emit light of its own, so the standard review format will not be used and the product will not be assigned a rating.


This is the SkyScan digital atomic alarm clock.

It keeps correct time by occasionally linking up with the atomic clock in Fort Collins CO. USA; you never really have to reset the time -- not even after Daylight Saving Time begins or ends.

FWIW: This is model number 31981B.
It must be obsolete now, as it was not found on the SkyScan website.


Size of product w/hand to show scale SIZE



To use this clock, install two AAA cells (see directly below), and THEN you can go check the time.

Setting this clock is quite easy...actually, you don't have to set it unless you need to know the time & date ***RIGHT AWAY***.


TO SELECT THE TIME ZONE:

1. Press TIME ZONE button once, the LCD shows the time zone (the default time zone is PST).
2- Press + or - - to set the time zone (PST>MST>CST>EST)
3. Press the TIME ZONE or SET button to go back to the time display or it will automatically go back to the time display in 5 seconds.

TO SET TIME, CALENDAR, 12/24HR AND C/F:

1. Press the SET button once to set the Year: digits show '2003" and blink. Press + or - - to set the year.
2. Press the SET button again to set the Date : small digits show " 1 - 1" (i.e. Jan 1st) and blink. Press + or - - to set the date. Press and hold + or - will increase the increment or decrement at a faster rate.
3. Press the SET button again to set the Time : large digits in HR : MIN will show and blink.
Press + or - to set the clock to the current time. Press and hold + or - will increase increment or decrement at a faster rate.
4. Press the SET button again to set 12 / 24 HR readout. Upper LCD shows "l2Hr" and blink.
Press + or - to choose 12HR or 24 HR time display format.
5. Press the SET button again to select C/Freadout: the temperature readout (i.e. 68F) will blink. Press + or - to choose readout (i.e. 68F or 20C ). The default readout is In degree F.
6. Press the SET button again to exit the setting mode and return to the normal display. Or it will automatically return in 5 seconds. **Special attention for usage in Arizona and Indiana.**

Part of Arizona and Indiana do not have Daylight Saving Time (DST). Please slide the DST switch inside the battery compartment to OFF if the clock is used in these states.

TO SET ALARM TIME:
1. To read your alarm time: press + or - once, the lower Month and Date digits will change to alarm time digits.
2. To set the alarm time: press + or - again, the alarm digits will blink, Press + or - - to set your alarm time. Press and hold + or - will increase the increment or decrement at a faster rate.
3. Alter you set the alarm, the clock will go back to the normal display automatically in 5 seconds.

TO TURN ON/OFF THE ALARM:
1. To use snooze alarm
Press the SNOOZE / AL ON/0FF button until SNZ and (((o))) show on lower LCD.
When the alarm beeps, press SNOOZE / LIGHT bar. The alarm will Sound again when the snooze period is over. (See "To Program the Snooze Alarm " below)
When the alarm beeps, press any key at the front to stop the alarm. The snooze alarm will turn on the following day at the same time.
2. To turn on alarm
Press the SNOOZE /AL ON/OFF button until (((o))) shows on lower LCD.
When the alarm beeps, press SNOOZE / LIGHT. The alarm will turn on the following day at the same time. 3. To disable the alarm permanently:
Press the SNOOZE / AL ON / 0FFbutton until the SNZ and (((o))) clear from the lower LCD.

TO PROGRAM THE SNOOZE ALARM:
1. Press and hold the SNOOZE I LIGHT bar for 3-4 seconds. The small display will blink and show 05 (minutes) the default snooze duration. Press + or - to set the snooze duration from 5 minutes to 60 minutes.
Note: The minimum snooze duration is 5 minutes.
2. Press the SNOOZE I LIGHT bar once to go back to the normal display or the clock will auto exit if no further buttons are pressed after 5 seconds.


The above instructions were lifted from this web page, as I no longer have the instructional materials that were furnished with this product.



To change the AAA cells when necessary, place the clock face-down on a soft surface like a bed, uphostered chair, couch, etc. and look on the back for a battery door near the bottom. Lift this door off, carry it to a bridge over deep water (the Brooklyn Bridge would be ideal; however, the Juneau-Douglas Bridge would also do in a pinch here), and throw it over the side so that it goes "blub blub blub" all the way to the bottom of Gastineau Channel with all of the bowling balls that were lobbed over that bridge in the 1950s and 1960s...O WAIT!!! YOU'LL NEED THAT!!! So just set it aside instead.

You'll see two AAA cells in the compartment. Remove them, and dispose of or recycle them as you see fit.

Insert two new AAA cells into the compartment, orienting them according to the polarity legend embossed into the bottom of the compartment.

Place the battery door back on, and slide it upward until it fits flush with the clock body.
Aren't you glad that you didn't throw that battery door over the side of the Juneau-Douglas Bridge now?


This is what the Juneau-Douglas Bridge looks like...or what it lookED like anyway before it was replaced in 1976.


And this is what the bridge looks like now.



Photograph of this clock's display; backlighting was turned on.


Spectrographic analysis
Spectrographic analysis of the (suspected) EL backlight.


Spectrographic analysis
Same as above; known dark conditions were used this time in an attempt to (unsuccessfully) eliminate the spectral feature visible in the NIR portion of the spectrum.


Audio (sound) file {.WAV format} of this clock's alarm.

This file is ~0.255 megabytes (267,017 bytes) in size; dial-up users please be aware.








TEST NOTES:
Unit was purchased on Ebay possibly in 2000.

Product was made in China.
A product's country of origin really does matter to some people, which is why I published it on this web page.


UPDATE: 00-00-00



    MANUFACTURER: SkyScan
    PRODUCT TYPE: Digital alarm clock
    LAMP TYPE: Possible EL display backlighting
    No. OF LAMPS: 1
    BEAM TYPE: N/A
    SWITCH TYPE: N/A
    CASE MATERIAL: Plastic
    BEZEL: Plastic; display protected by plastic window
    BATTERY: 2x AAA cells
    CURRENT CONSUMPTION: Unknown/unable to measure
    WATER- AND PEE-RESISTANT: No
    SUBMERSIBLE: NO WAY HOZAY!!!
    ACCESSORIES: None
    WARRANTY: Unknown/TBA

    PRODUCT RATING:

    Product was not intended to be a light-emitter, so the traditional "star" rating will not be used.





SkyScan Digital Atomic Alarm Clock *






Do you manufacture or sell an LED flashlight, task light, utility light, or module of some kind? Want to see it tested by a real person, under real working conditions? Do you then want to see how your light did? If you have a sample available for this type of real-world, real-time testing, please contact me at ledmuseum@gmail.com.

Please visit this web page for contact information.

Unsolicited flashlights, LEDs, and other products appearing in the mail are welcome, and it will automatically be assumed that you sent it in order to have it tested and evaluated for this site.
Be sure to include contact info or your company website's URL so visitors here will know where to purchase your product.


WHITE 5500-6500K InGaN+phosphor 
ULTRAVIOLET 370-390nm GaN 
BLUE 430nm GaN+SiC
BLUE 450 and 473nm InGaN
BLUE Silicon Carbide
TURQUOISE 495-505nm InGaN
GREEN 525nm InGaN 
YELLOW-GREEN 555-575mn GaAsP & related
YELLOW 585-595nm
AMBER 595-605nm
ORANGE 605-620nm
ORANGISH-RED 620-635nm
RED 640-700nm
INFRARED 700-1300nm
True RGB Full Color LED
Spider (Pirrahna) LEDs
SMD LEDs
True violet (400-418nm) LEDs
Agilent Barracuda & Prometheus LEDs
Oddball & Miscellaneous LEDs
Programmable RGB LED modules / fixtures
Where to buy these LEDs 
Links to other LED-related websites
The World's First Virtual LED Museum
Legal horse puckey, etc.
RETURN TO OPENING/MAIN PAGE
LEDSaurus (on-site LED Mini Mart)



This page is a frame from a website.
If you arrived on this page through an outside link,you can get the "full meal deal" by clicking here.