RED LED FLASHER BOARD

Red LED Flasher Board, retail $TBA
Manufactured by (Unknown)
Last updated 09-13-10




This is an LED flasher board, probably originally designed to go inside something to attract your attention at a grocery or other store.

It has a 3mm red LED at its center, and is powered by 1, 2, or 3 CR2032 lithium coin cells.


Size of product w/hand to show scale SIZE



This flasher fires off automatically after you install one or more batteries in it.



To change the batteries in the Red LED Flasher Board, use a small standard screwdriver to push the dead CR2032 lithium coin cells partially out of their carriers from the inside edge that has a cutout expressly for this purpose. Once the cells have been partially pushed out, you may grasp them with your fingers, pull them the rest of the way out, and dispose of or recycle them as you see fit.

Insert at least one CR2032 lithium coin cell into any one of the carriers, orienting it so that its button-end (-) negative faces down, and the product will automatically spring to life.

You may simply leave the other two carriers empty if desired, but installing batteries into them will give you a longer time between battery changes.



This is an LED flasher board designed to go in something, not a flashlight designed to be thrashed, trashed, and abused. So I won't throw it against the wall, stomp on it, try to drown it in the toylet bowl or the cistern, run over it, swing it against the concrete floor of a porch, use a small sledgehammer in order to bash it open to check it for candiosity, fire it from the cannoņata, drop it down the top of Mt. Erupto (I guess I've been watching the TV program "Viva Piņata" too much again - candiosity is usually checked with a laser-type device on a platform with a large readout (located at Piņata Central), with a handheld wand that Langston Lickatoad uses, or with a pack-of-cards-sized device that Fergy Fudgehog uses; the cannoņata (also located at Piņata Central) is only used to shoot piņatas to piņata parties away from picturesque Piņata Island, and Mt. Erupto is an active volcano on Piņata Island {In the episode "Les Saves the Day...Again", Paulie Preztail says "Hey, ever wonder why this park's called 'Mount Erupto' anyway?", then Franklin Fizzlybear says "I think its an old native term. Means 'very safe.'"}), send it to the Daystrom Institute for additional analyses, or inflict upon it punishments that a flashlight might have to have performed on it. So this section of the web page will be ***SIGNIFICANTLY*** more bare than this section of the web page on a page about a flashlight.





This is a screen dump of the video below that shows the LED in its "ON" state.


Spectrographic analysis
Spectrographic analysis of the LED in this flasher.

USB2000 spectrometer graciously donated by P.L.




A video clip on YourTube showing this product flashing.

This clip is approximately 7.956572355783 megabytes (8,195,530 bytes) in length; dial-up users please be aware.
It will take no less than forty minutes to load at 48.0Kbps.






TEST NOTES:
I've had this product for quite a number of years; I no longer remember where it came from.


UPDATE: 00-00-00






    MANUFACTURER: Unknown
    PRODUCT TYPE: Self-contained LED flasher board
    LAMP TYPE: 3mm red LED
    No. OF LAMPS: 1
    BEAM TYPE: N/A
    SWITCH TYPE: None
    CASE MATERIAL: Printed circuit board
    BEZEL: N/A
    BATTERY: 1x, 2x, or 3x CR2032 lithium coin cells
    CURRENT CONSUMPTION: Unknown/unable to measure
    WATER- AND URANATION-RESISTANT: No
    SUBMERSIBLE: FOR CHRIST SAKES NOOOOO!!!
    ACCESSORIES: None that I'm aware of
    SIZE: 57mm L x 50mm L x 11mm D
    WEIGHT: Unknown (not equipped to weigh)
    COUNTRY OF MANUFACTURE: Unknown
    WARRANTY: Unknowm

    PRODUCT RATING:

    Product is designed to be installed in a finished product,
    so I cannot in good conscience furnish it with a "star" rating.





Red LED Flasher Board *






Do you manufacture or sell an LED flashlight, task light, utility light, or module of some kind? Want to see it tested by a real person, under real working conditions? Do you then want to see how your light did? If you have a sample available for this type of real-world, real-time testing, please contact me at ledmuseum@gmail.com.

Please visit this web page for contact information.

Unsolicited flashlights, LEDs, and other products appearing in the mail are welcome, and it will automatically be assumed that you sent it in order to have it tested and evaluated for this site.
Be sure to include contact info or your company website's URL so visitors here will know where to purchase your product.








This page is a frame from a website.
If you arrived on this page through an outside link,you can get the "full meal deal" by clicking here.