PEAK 1xN 1x LED FLASHLIGHT

Peak LED Solutions 1xN 1x LED Flashlight, retail $24.95 (http://peakledsolutions.net...)
Manufactured by Peak LED Solutions (http://peakledsolutions.net/)
Last updated 08-08-04




(IMPORTANT: The Peak LED Solutions website is currently under construction)

This is the Peak LED Solutions 1xN 1xLED flashlight.
It is labelled as coming from the Shasta Collection; flashlights that use a single N cell and have 1 or 3 LEDs.

Ths unit comes in an aluminum body, with a Type III hard anodized finish on it.

There is 1 white LED in the head, and an N cell inside the barrel powers it.


SIZE



The light came to me ready to use, with a Panasonic Heavy-Duty N cell already installed.

To turn the light on, twist the bezel (head) clockwise (as if tightening it). And to turn the light off, turn the bezel counterclockwise (as if loosening it) about 1/8 of a turn from the fully tightened position.



To feed your light, unscrew the bezel (head) until it comes off (don't worry about losing parts or bulbs) and throw it out a window as hard as you can...O WAIT, YOU'LL NEED THAT!!! So just set it aside instead. ;-)

Tip the barrel into your hand so the used N cell falls out. Dispose of or recycle it as you see fit.

Drop a new N cell in the barrel, flat-side (-) negative first, so the button-end is showing. Screw the bezel back on, and you're finished. Oh, and unscrew that bezel slightly when your Peak springs to life. You don't want to waste a brand spanken new battery ya know.
Aren't you glad you didn't throow that bezel out the window now? ;-)

Unable to measure current usage due to how the flashlight is constructed.




Photograph showing the business-end of the flashlight.

The Peak is very durable, and ordinary flashlight accidents (dropping it, whapping it against a doorframe or car door in alarm, sitting on it, stepping on it, sucking it up the vaccume cleaner, etc.) will not damage it. I hit it against a steel rod 11 times (6 against the tailcap, 5 against the bezel), and did not damage the flashlight in any way I can see, and it still works correctly too. Very few flashlights are damaged or destroyed by this test however; maybe I need to come up with something even more awful.

I ran over the Peak several times with the rear drive wheels of a 400 pound electric wheelchair, and no damage was expected or found.

The Peak has an O-ring that seals the bezel against the barrel, so it should be fully weatherproof, and maybe even submersible to at least a foot or two. Let's try the sink-with-water-in-it test and see what happens...BRB...ok, after submerging it for three minutes in about a foot of water at 69°F (20.5°C) (to simulate a user dropping it into a creek), I dried the outside off with some buttwipe, unscrewed the bezel, and there was no water inside. So yes, weatherproof and submersible to at least 1 foot.
I also tried suctioning the bezel by itself to be sure no leakage occurred around the LED, and no leakage was detected.
If it falls into water, just shake it off and keep going. If it falls into seawater or if the dog goes #1 on it, douche it off with fresh water, shake it off (or dry it off) and it ought to be good as new.

There is a light knurling (texturising) present on the barrel of the Peak; this helps to aid in retention (the ability to hold onto the flashlight when your hands are cold, wet, or oily). This knurling is not aggressive (sharp), so it won't cut a hole in your pocket if you carry the Peak that way. The bezel (head) has what I believe is a 12-sided shape machined into it. Although this does not function as an anti-roll device, it does help a bit to aid in your grip when you turn the flashlight on and off.

The Peak is equipped with a small split ring on its tail, so you can affix it to a keychain and carry it that way if you desire.

The very tail end is removeable (by unscrewing it), to allow the flashlight to be affixed to a large and sturdy magnetic clamp assembly that you can get from Peak LED Solutions.


This clip has a large, heavy-duty clamp with very strong jaws, a large ceramic ring magnet in its base (under that shiny metal thing at the bottom), and a flexible arm that can be positioned pretty much anywhere.
Once the flashlight's very tail end is unscrewed and removed, the flashlight can then be screwed onto the end of the red arm (a Peak brass CR123A cell 7xLED flashlight is shown in this photograph), and pretty much aimed wherever you need light.

You can also stand the Peak on its tail end when this piece is unscrewed; you can stand it on a dresser, counter, table, or other flat surface and let the light reflected off the ceiling light up the entire room.

There appears to be a regulation circuit inside the bezel (head), potted in a black epoxy compound. This circuit feeds the LEDs constant power until the battery can no longer provide that power, then the intensity of the LEDs rather quickly falls off. This is your cue to change the battery. You aren't just plunged into instant darkness, as can happen with some other regulated flashlights.

The flashlight uses a white LED, so you can light a room with it by removing the tailpiece and standing it up.



Beam photo at ~12".
Measures 15,090mcd on a Meterman LM631 light meter.



TEST NOTES:
Test unit was sent by MJ of Peak LED Solutions along with twelve of their other flashlights, and was received on 08-04-04.


Here's an example of the retail packaging these flashlights come in.


UPDATE: 00-00-00



PROS:
Durable construction
Waterproof, submersible to at least 12"
Knurled, to aid in retention
Tailcap can be removed to allow flashlight to stand on-end
Uses a cell that is common and relatively inexpensive
Battery rattle problem has been solved


CONS:



    MANUFACTURER: Peak LED Solutions
    PRODUCT TYPE: Keychain flashlight
    LAMP TYPE: 5mm white LED
    No. OF LAMPS: 1
    BEAM TYPE: Narrow flood, with soft fall-off at perimeter
    SWITCH TYPE: Twist bezel on/off
    BEZEL: Metal; LED recessed into a conical "reflector"
    BATTERY: 1 N cell
    CURRENT CONSUMPTION: Unknown/unable to measure
    WATER RESISTANT: Yes
    SUBMERSIBLE: Yes, to at least 12"
    ACCESSORIES: 1 N cell
    WARRANTY: 1 year

    PRODUCT RATING:

    Star RatingStar Rating





Peak LED Solutions 1xN 1xLED Flashlight * http://peakledsolutions.net...






Do you manufacture or sell an LED flashlight, task light, utility light, or module of some kind? Want to see it tested by a real person, under real working conditions? Do you then want to see how your light did? If you have a sample available for this type of real-world, real-time testing, please contact me at ledmuseum@gmail.com.

Please visit this web page for contact information.

Unsolicited flashlights appearing in the mail are welcome, and it will automatically be assumed that you sent it in order to have it tested and evaluated for this site.
Be sure to include contact info or your company website's URL so visitors here will know where to purchase your product.


WHITE 5500-6500K InGaN+phosphor 
ULTRAVIOLET 370-390nm GaN 
BLUE 430nm GaN+SiC
BLUE 450 and 473nm InGaN
BLUE Silicon Carbide
TURQUOISE 495-505nm InGaN
GREEN 525nm InGaN 
YELLOW-GREEN 555-575mn GaAsP & related
YELLOW 585-595nm
AMBER 595-605nm
ORANGE 605-620nm
ORANGISH-RED 620-635nm
RED 640-700nm
INFRARED 700-1300nm
True RGB Full Color LED
Spider (Pirrahna) LEDs
SMD LEDs
True violet (400-418nm) LEDs
Agilent Barracuda & Prometheus LEDs
Oddball & Miscellaneous LEDs
Programmable RGB LED modules / fixtures
Where to buy these LEDs 
Links to other LED-related websites
The World's First Virtual LED Museum
Legal horse puckey, etc.
RETURN TO OPENING/MAIN PAGE
LEDSaurus (on-site LED Mini Mart)



This page is a frame from a website.
If you arrived on this page through an outside link,you can get the "full meal deal" by clicking here.