Garrity Aluminum LED Flashlight, retail $12.77 ()
Manufactured by Garrity (
Last updated 09-12-13

The Garrity Aluminum LED Flashlight (for lack of a better name; because this is what it reads on the package) is an almost all-aluminum flashlight that features a 5mm Nichia brand white LED behind a convex (positive, magnifying) lens, feeds from three AAA cells held in a side-by-side carriage in the flashlight's barrel, and has red & blue filters that fit over the lens to change the color of the beam.


To use this flashlight, feed it first (see directly below), and then you can go to town.

Firmly press and release the rubberised button on the tailcap to turn the flashlight on.
Firmly press & release it again to turn the flashlight off.

There is no momentary or signalling mode available when the flashlight is off, however, you can blink the flashlight while it is on by partially depressing the tailcap button. If you don't mind the backward or reverse feeling of this, you can blink the flashlight this way.

This Garrity flashlight comes with color filters for red and blue. To use one, hold it up to the flashlight's "business-end", orienting it so the larger of the two sides faces the flashlight. Press it straight on until it snaps into place.
To remove the filter when you are finished using it, just pull it straight off.

The flashlight comes with a nylon pouch/belt holster. The flashlight fits this holster bezel-up or bezel-down; a flap with velcro on it folds over the top and attaches to the body of the holster, so the flashlight doesn't just fall out. This holster fits belts up to 2" wide. I do not own or use pants that require a belt however, so I cannot test this accessory in the manner in which it was intended to be used.

The two color filters fit in a pocket on the side of this holster; a velcro flap closes over the opening so the filters don't just fall out and become broken or lost.

To change the batteries in your flashlight, unscrew and remove the tailcap, dash it to the ground, look at it all funny, cock your head like a puppy that doesn't understand what it had just been told, and stomp on it with the heels of spiked golf shoes...O WAIT!!! YOU'LL NEED THAT!!! So just set it aside instead.

Tip the black plastic battery carriage out of the barrel and into your hand. If necessary, remove and dispose of or recycle the used AAA cells if they are present in this carriage.

Insert three new AAA cells into the carriage, one in each compartment. Orient each cell so the flat-end (-) negative faces a spring for it in its compartment.

Once the carriage is full, insert it into the flashlight's barrel, aiming it so the spring on the end goes in first. Screw the tailcap back on, and be done with it.
Aren't you glad you didn't stomp on that tailcap now?

Current usage measures 73.0mA on my DMM's 400mA scale.

The flashlight appears to be reasonably sturdy. Ordinary flashlight accidents should not be enough to do it in. I administered the smack test on it (ten whacks against the corner of a concrete stair; five whacks against the side of the tailcap and five whacks against the side of the bezel), and found the expected damage. There is some minor gouging on the sides of the tailcap and bezel where it was struck. No optical or electrical malfunctions were detected.

I believe it has a Type II anodized finish. I was relatively easily able to put a scratch (to bare metal) in it with the blade of a Swiss army knife. So it probably really does has a Type II anodized finish.
Would I really try to cut up a brand spanken new flashlight?
You bet your sugar-coated toilet muscle (sweet patootie) I would, if it's in the name of science.

The flashlight is weather- and water-resistant, and is even submersible to shallow depths at the very least. When I removed the tailcap, relieved the barrel of its battery carriage, and then performed that dreadful suction test, no leakage was detected. So if it fell into shallow water, just shake it off and keep going. And you need not be concerned about using it in rain or snow. And if it fell next to the mailbox and the dog pissed on it, just take the garden hose to it or douche it off under the faucet...good as new!

The light it produces (with no filters in place) consists of a white circle with a blue ring right at the perimeter; this is perfectly normal for a lensed LED like this and is nothing whatsoever to be concerned about.

Beam photograph (white) on the test target at 12".
Measures 76,100mcd on a Meterman LM631 light meter.
This measurement is high primarily because of the magnifying lens in front of the LED.

Beam photograph (red) on the test target at 12".
Measures 6,330mcd on a Meterman LM631 light meter.

Beam photograph (blue) on the test target at 12".
Measures 14,680mcd on a Meterman LM631 light meter.

Spectrographic plot
Spectrographic analysis of the LED (unfiltered) in this flashlight.

Spectrographic plot
Spectrographic analysis of the LED (red filter) in this flashlight.

Spectrographic plot
Spectrographic analysis of the LED (blue filter) in this flashlight.

Spectrographic analysis
Spectrographic analysis of the LED (no filter) in this flashlight; newest (01-13-13) spectrometer software settings used.

Spectrographic analysis
Spectrographic analysis of the LED (no filter) in this flashlight; newest (01-13-13) spectrometer software settings used. Spectrometer's response narrowed to a band between 440nm and 450nm to pinpoint native emission peak wavelength, which is 445.170nm.

The raw spectrometer data (tab-delimited that can be loaded into Excel) is at

USB2000 Spectrometer graciously donated by P.L.

ProMetric analysis
Beam cross-sectional analysis.
Image made using the ProMetric System by Radiant Imaging.

Test unit was sent by S.C. of Garrity along with three other products, and was received on 09-29-05

Flashlight was made in China. A product's country of origin really does matter to some people, which is why I published it on this page.

UPDATE: 00-00-00



    PRODUCT TYPE: Handheld flashlight
    LAMP TYPE: 5mm white LED
    No. OF LAMPS: 1
    BEAM TYPE: Medium spot w/very sharp perimeter; almost no corona
    SWITCH TYPE: Rubberised pushbutton on/off on tailcap
    BEZEL: Metal; LED protected by plastic optic
    BATTERY: 3xAAA cells
    SUBMERSIBLE: Yes, to shallow depths at minimum
    ACCESSORIES: 3xAAA cells, two color filters, nylon belt holster, wrist lanyard
    WARRANTY: Lifetime


    Star Rating

Garrity Aluminum LED Flashlight *

Do you manufacture or sell an LED flashlight, task light, utility light, or module of some kind? Want to see it tested by a real person, under real working conditions? Do you then want to see how your light did? If you have a sample available for this type of real-world, real-time testing, please contact me at

Please visit this web page for contact information.

Unsolicited flashlights, LEDs, and other products appearing in the mail are welcome, and it will automatically be assumed that you sent it in order to have it tested and evaluated for this site.
Be sure to include contact info or your company website's URL so visitors here will know where to purchase your product.

WHITE 5500-6500K InGaN+phosphor 
ULTRAVIOLET 370-390nm GaN 
BLUE 430nm GaN+SiC
BLUE 450 and 473nm InGaN
BLUE Silicon Carbide
TURQUOISE 495-505nm InGaN
GREEN 525nm InGaN 
YELLOW-GREEN 555-575mn GaAsP & related
YELLOW 585-595nm
AMBER 595-605nm
ORANGE 605-620nm
ORANGISH-RED 620-635nm
RED 640-700nm
INFRARED 700-1300nm
True RGB Full Color LED
Spider (Pirrahna) LEDs
True violet (400-418nm) LEDs
Agilent Barracuda & Prometheus LEDs
Oddball & Miscellaneous LEDs
Programmable RGB LED modules / fixtures
Where to buy these LEDs 
Links to other LED-related websites
The World's First Virtual LED Museum
Legal horse puckey, etc.
LEDSaurus (on-site LED Mini Mart)

This page is a frame from a website.
If you arrived on this page through an outside link,you can get the "full meal deal" by clicking here.